Skip To Content

Work 01 Of 09

Vessel ForA Low Tide

Year
2026
Materials
Estuary terracotta, iron slip, beeswax
Dimensions
H 112 × Ø 68 cm
Series
Low Water
Vessel For A Low Tide: a round, burnished terracotta vessel on grey concrete in soft side light

Placeholder photograph. Swap for the finished piece in situ.

The clay for this vessel came out of the estuary in March, on the lowest tide of the year. I dug it from the bank below the old saltworks with a spade and a bucket, the way the brickmakers here did a century ago, and carried it up to the studio in eleven trips. It is a stubborn body: rich in iron, loaded with fine sand, and quick to crack if it is rushed.

I let it sour through the summer in covered bins, turning it once a week. Souring is a kind of listening. The clay grows more plastic as the life in it works, and the smell changes from river to something closer to bread. By September it would stand up in a coil as thick as my wrist without slumping, and that is when I began.

A vessel this size cannot be forced. It rises at the speed the clay allows, and not a day sooner.

From The Studio Notes

The walls went up over six weeks, one coil at a time, each one pinched into the last and smoothed with a rib cut from a piece of driftwood. At the belly the form reaches sixty eight centimetres across, and there it has to be held: wrapped in damp cloth overnight, opened again each morning, checked for the slow lean that tells me the shoulder wants to fall.

I wanted the shoulder to feel like the moment a tide turns, a long outward breath that pauses before drawing in. The neck narrows sharply, then flares at the lip just enough to catch the light. The iron slip band was brushed on at leather hard and scored with a comb cut from a shell, so the marks run around the vessel like the ripples left on wet sand.

Burnishing took four days. I worked the surface with a river stone in small circles until the clay closed and began to shine, then rested it, then worked it again. There is no glaze on this piece. What you see is pressure and time, and the warmth of the hand that did it.

The kiln has the last word. I only choose what to pack around the foot, and how long to wait before opening the door.

From The Studio Notes

It was fired once, slowly, to 980°C, in a saggar packed with sea salt, kelp and copper wire. The salt flashed the lower body to a soft rose and the kelp left the pale shadows that gather near the foot. None of those marks were drawn. They are a record of where the fire moved and where it lingered.

Vessel For A Low Tide was first shown in Low Water at Gallery Ostrand. It is meant to stand on the floor, at the height of a seated person, in a room with one good window. It holds nothing, and it is not empty.

From Kiln To Shelf, In Four Frames

Clay pots glowing red inside the long brick tunnel of a kiln

01 / 04

Packed For The Kiln

The night before the firing, every piece nested in salt, kelp and copper wire.

A tall stack of terracotta pots nested together in strong sunlight and shadow

02 / 04

Cooling In The Yard

Test pieces from the same clay bed, stacked to cool and read one by one for colour.

Three brown clay vessels of different heights standing together

03 / 04

Beside Its Studies

Shown with two smaller studies that tried the shoulder three different ways.

A wooden shelf lined with rows of brown terracotta pots

04 / 04

Back On The Shelf

The working shelf, where everything waits a week before it leaves the studio.

ProcessBeside Outcome

Week three on the left, the finished vessel on the right. The same hands, the same clay, twenty weeks and one firing apart.

Hands covered in wet clay shaping the rim of a vessel
ProcessWeek Three, Pinching The Shoulder Coil
The finished vessel, burnished terracotta standing on grey concrete
OutcomeFired, Burnished And Waxed

Details

Available by enquiry. Crated and delivered by the studio, and placed in the room by hand.

Enquire About This Work
Title
Vessel For A Low Tide
Year
2026
Series
Low Water
Materials
Estuary terracotta, iron slip, beeswax finish
Dimensions
Height 112 cm, widest 68 cm, mouth 31 cm
Weight
41 kg
Making Time
Seven months, clay bed to kiln
Firing
Single firing to 980°C in a saggar of salt and kelp
Edition
Unique
First Shown
Low Water, Gallery Ostrand, 2026
Availability
Available by enquiry
Care
Indoors, away from frost. Dust with a dry cloth.

Next Project, Work 02

Salt Choir

Three vessels, 2025. Continue through the works, one piece at a time.

View The Next Project
Back To All WorksWork 01 Of 09